From BlenderWiki

Jump to: navigation, search
Blender3D FreeTip.gif
IMPORTANT! Do not update this page!
We have moved the Blender User Manual to a new location. Please do not update this page, as it will be locked soon.


Celkové nastavení geometrie

V této záložce se řídí geometrie jednotlivých tahů.


Je dostupných celkem třináct geometrických modifikátorů. Mají za úkol upravovat, deformovat dvojrozměrné freestyle tahy.

Tak jako je v Blenderu obvyklé, modifikátory jsou uplatňovány v zásobníku odzhora dolů.

2D Posuv

Tento 2D Offset - posuv modifikátor přidává jednoduchý posuv linek. Má dvě skupiny nezávislých voleb / efektů:

Modifikátor posuvu čar "2D Offset"
Start a End-konec
Tyto dvě volby určují velikost posuvu u začátku a konce čáry podél 2D normály. Výsledek je vytvoření "obalové křivky". Pokud například nastavíme Start na hodnotu 50, bude počátek tahu posunut 50 pixelů, střed čáry bude 25 pixel. a konec tahu nebude posunut vůbec.
X a Y
Tyto dvě volby jednoduše přidají horizontální a vertikální posuv celému tahu.

Transformace 2D

Line Style Geometry's 2D Transform modifier

The 2D Transform modifier applies two-dimensional scaling and/or rotation to the stroke backbone geometry. Scale is applied before rotation.

The center (pivot point) of these 2D transformations can be:

Stroke Center
The median point of the stroke.
Stroke Start
The beginning point of the stroke.
Stroke End
The end point of the stroke.
Stroke Point Parameter
The Stroke Point Parameter factor controls where along the stroke the pivot point is (0.0 means start point; 1.0 end point).
Absolute 2D Point
The Pivot X and Pivot Y allows you to define the position of the pivot point in the final render (from the bottom left corner). WARNING: Currently, you have to take into account the real render size, i.e. resolution and resolution percentage!
Scale X and Scale Y
The scaling factors, in their respective axes.
Rotation Angle
The rotation angle.
2D Transform modifier File:Toycar Three

Backbone Stretcher

Line Style Geometry's Backbone Stretcher modifier

The Backbone Stretcher modifier stretches (adds some length to) the beginning and end of the stroke.

Backbone Length
Length to add to the strokes’ ends.

Bezier Curve

Line Style Geometry's Bezier Curve modifier

The Bezier Curve modifier replaces the stroke by a Bezier approximation of it.

The maximum distance allowed between the new Bezier curve and the original stroke.
Bezier Curve modifier demo by T.K. File:Toycar


Line Style Geometry's Blueprint modifier

The Blueprint modifier produces blueprint-like strokes using either circular, elliptical, or square contours. A blueprint here refers to those lines drawn at the beginning of free-hand drawing to capture the silhouette of objects with a simple shape such as circles, ellipses and squares.

Which base shapes to use for this blueprint: Circles, Ellipses or Squares.
How many rounds are generated, as if the pen draws the same stroke several times (i.e. how many times the process is repeated).
Random Radius and Random Center
For the Circles and Ellipses shapes. Adds some randomness to each round in the relevant aspect. Using more than one round with no randomness would be meaningless, as they would draw over each other exactly.
Backbone Length and Random Backbone
For the Squares shapes. The first adds some extra length to each edge of the generated squares (also affected by the second parameter). The second adds some randomness to the squares.

Note that the Min 2D Length feature from the Strokes settings is quite handy here, to avoid the noise generated by small strokes…

Guiding Lines

Line Style Geometry's Guiding Lines modifier

The Guiding Lines modifier replaces a stroke by a straight line connecting both of its ends.

Offset the start and end points along the original stroke, before generating the new straight one.

This modifier will produce reasonable results when strokes are short enough, because shorter strokes are more likely to be well approximated by straight lines. Therefore, it is recommended to use this modifier together with one of the splitting options (by 2D angle or by 2D length) from the Strokes panel.

Guiding Lines modifier Demo by T.K. File:Toycar Guiding

Perlin Noise 1D

Line Style Geometry's Perlin Noise 1D modifier

The Perlin Noise 1D modifier adds one-dimensional Perlin noise to the stroke.

How dense the noise is (kind of a scale factor along the stroke).
How much the noise distorts the stroke in the Angle direction.
The seed of the random generator (the same seed over a stroke will always give the same result).
The “level of detail” of the noise.
In which direction the noise is applied (0.0° is fully horizontal).

Perlin Noise 2D

Line Style Geometry's Perlin Noise 2D modifier

The Perlin Noise 2D modifier adds one-dimensional Perlin noise to the stroke.

Its settings are exactly the same as the Perlin Noise 1D modifier.

TODO: What’s the difference between those two modifiers?


Line Style Geometry's Polygonization modifier

The Poligonization modifier simplifies strokes as much as possible (in other words, it transforms smooth strokes into jagged polylines).

The maximum distance allowed between the new simplified stroke and the original one (the larger this value is, the more jagged/approximated the resulting polylines are).


Line Style Geometry's Sampling modifier

The Sampling modifier changes the definition, precision of the stroke, for the following modifiers.

The smaller this value, the more precise are the strokes. Be careful; too small values will require a huge amount of time and memory during render!

Sinus Displacement

Line Style Geometry's Sinus Displacement modifier

The Sinus Displacement modifier adds a sinusoidal displacement to the stroke.

How wide the undulations are along the stroke.
How high the undulations are across the stroke.
Allows “offsetting” (“moving”) the undulations along the stroke.
Sinus Displacement modifier demo by T.K. File:Toycar

Spatial Noise

Line Style Geometry's Spatial Noise modifier

The Spatial Noise modifier adds some spatial noise to the stroke.

TODO: definition of "spatial noise"!

How much the noise distorts the stroke.
How wide the noise is along the stroke.
The level of detail of the noise.
When enabled, apply some smoothing over the generated noise.
Pure Random
When disabled, the next generated random value depends on the previous one; otherwise they are completely independent. Disabling this setting gives a more “consistent” noise along a stroke.

Tip Remover

Line Style Geometry's Tip Remover modifier

The Tip Remover modifier removes a piece of the stroke at its beginning and end.

Tip Length
Length of stroke to remove at both of its tips.